Understanding Plumbing Basics is Vital for Bathtub Installation
Understanding Plumbing Basics is Vital for Bathtub Installation
Blog Article
How do you really feel about How to Install a Bathtub Yourself?
Installing a bathtub isn't precisely brain surgery, however it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a new one is likewise a reasonably difficult task. If the old bathtub is easily obtainable, the project can relocate easily; if you need to open up a wall to remove the old bathtub and place the new bathtub, the task is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the new one. See to it you have qualified yourself for the work and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one before you start. Opportunities are you might need a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your restroom if you have actually currently purchased a brand-new tub as well as do not need to alter the arrangement of your previous water pipes.
Your tools and also product list ought to consist of the following:
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Making use of the two wood boards under its feet, put the tub in the required position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the bathtub until the level reviews level.
To set up faucets, fit the bottom of the furthest adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the bath tub and also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washers are in place in between the faucet and the sink. Safeguard the faucet in place with the producer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, causing issues with moisture as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealant can split fairly very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that piece of writing about How to Install a Bathtub when doing a lookup on the web. Feel free to take the time to promote this blog posting if you liked it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Emergency? We're ready. Report this page